This script forwards traffic from one interface to another. It's primary use is for setting up a router in WiFiDog. I've added a rule to prevent wireless client users accessing the gateway machine on port 22.

#!/bin/sh 
# IPTABLES  PROXY  script for the Linux 2.4 kernel.
# This script is a derivitive of the script presented in
# the IP Masquerade HOWTO page at:
# www.tldp.org/HOWTO/IP-Masquerade-HOWTO/firewall-examples.html
# It was simplified to coincide with the configuration of
# the sample system presented in the Guides section of
# www.aboutdebian.com
 
# This script is presented as an example for testing ONLY
# and should not be used on a production proxy server.
 
#    PLEASE SET THE USER VARIABLES
#    IN SECTIONS A AND B OR C
echo -e "\n\nSETTING UP IPTABLES PROXY..."
 
# === SECTION A ===
#   FOR EVERYONE SET THE INTERFACE DESIGNATION FOR THE NIC CONNECTED TO YOUR INTERNAL NETWORK
#   The default value below is for "eth0".  This value 
#   could also be "eth1" if you have TWO NICs in your system.
#   You can use the ifconfig command to list the interfaces
#   on your system.  The internal interface will likely have
#   have an address that is in one of the private IP address
#   ranges.
#   Note that this is an interface DESIGNATION - not
#   the IP address of the interface.
#   Enter the internal interfaces designation for the INTIF variable
 
 
INTIF="eth1"
 
 
#   SET THE INTERFACE DESIGNATION FOR YOUR "EXTERNAL" (INTERNET) CONNECTION
#   The default value below is "ppp0" which is appropriate 
#   for a MODEM connection.
#   If you have two NICs in your system change this value
#   to "eth0" or "eth1" (whichever is opposite of the value
#   set for INTIF above).  This would be the NIC connected
#   to your cable or DSL modem (WITHOUT a cable/DSL router).
#   Note that this is an interface DESIGNATION - not
#   the IP address of the interface.
#   Enter the external interfaces designation for the EXTIF variable:
 
 
EXTIF="eth0"
 
 
# ! ! ! ! !  Use ONLY Section B  *OR*  Section C depending on
#  ! ! ! !   the type of Internet connection you have.
# === SECTION B
# -----------   FOR THOSE WITH STATIC PUBLIC IP ADDRESSES
  # SET YOUR EXTERNAL IP ADDRESS
  #   If you specified a NIC (i.e. "eth0" or "eth1" for
  #   the external interface (EXTIF) variable above,
  #   AND if that external NIC is configured with a
  #   static, public IP address (assigned by your ISP),
  #   UNCOMMENT the following EXTIP line and enter the 
#   IP address for the EXTIP variable:
 
EXTIP="192.168.1.3"
 
# === SECTION C
# ----------   DIAL-UP MODEM, AND RESIDENTIAL CABLE-MODEM/DSL (Dynamic IP) USERS
# SET YOUR EXTERNAL INTERFACE FOR DYNAMIC IP ADDRESSING
#   If you get your IP address dynamically from SLIP, PPP,
#   BOOTP, or DHCP, UNCOMMENT the command below.
#   (No values have to be entered.)
#         Note that if you are uncommenting these lines then
#         the EXTIP line in Section B must be commented out.
#EXTIP="`/sbin/ifconfig ppp0 | grep 'inet addr' | awk '{print $2}' | sed -e 's/.*://'`"
# --------  No more variable setting beyond this point  --------
 
echo "Loading required stateful/NAT kernel modules..."
/sbin/depmod -a
/sbin/modprobe ip_tables
/sbin/modprobe ip_conntrack
/sbin/modprobe ip_conntrack_ftp
/sbin/modprobe ip_conntrack_irc
/sbin/modprobe iptable_nat
/sbin/modprobe ip_nat_ftp
/sbin/modprobe ip_nat_irc
echo "    Enabling IP forwarding..."
echo "1" > /proc/sys/net/ipv4/ip_forward
echo "1" > /proc/sys/net/ipv4/ip_dynaddr
echo "    External interface: $EXTIF"
echo "       External interface IP address is: $EXTIP" 
echo "    Loading proxy server rules..."
 
# Clearing any existing rules and setting default policy
 
iptables -P INPUT ACCEPT
iptables -F INPUT 
iptables -P OUTPUT ACCEPT
iptables -F OUTPUT 
iptables -P FORWARD DROP
iptables -F FORWARD 
iptables -t nat -F
 
#This is where you would probably want to put rules banning MAC addresses of naughty users
 
# FWD: Allow all connections OUT and only existing and related ones IN
iptables -A FORWARD -i $EXTIF -o $INTIF -m state --state ESTABLISHED,RELATED -j ACCEPT
iptables -A FORWARD -i $INTIF -o $EXTIF -j ACCEPT
 
# Chriss rule to stop port 22 traffic passing from wireless clients
 
iptables -A INPUT -p tcp -i $INTIF --dport 22 -j DROP
 
# Enabling SNAT (MASQUERADE) functionality on $EXTIF
 
iptables -t nat -A POSTROUTING -o $EXTIF -j MASQUERADE
echo -e "       Proxy server rule loading complete\n\n"
 
echo -e " We are now starting the DHCP server on eth1 \n\n"
dhcpd eth1